Teejet Matrix 840G User Manual Manuale Utente Pagina 22
- Pagina / 58
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
www.teejet.com
30
●
98-05141 R2
31
●
Touch Screen Calibration with
Software Version 1.03
Touch Screen Calibration is used to activate a touch
screen calibration.
1. Press CONSOLE ICON .
2. Press CALIBRATE TOUCH SCREEN ICON .
3. Press HAND ICON to enable the touch
screen calibration process.
4. “Begin touch screen calibration?”
Press
►Yes – to begin the Touch Screen Calibration.
►No – to return to the Touch Screen Calibration
screen
5. Press series of 5 crosshairs .
6. Press OK to complete the touch screen
calibration.
7. Press
►PAGE RIGHT ARROW to proceed to
Screenshot.
►SYSTEM SETUP TAB to return to main
System Setup screen.
Figure 2-25: Touch Screen Calibration
Figure 2-26: Touch Screen Calibration Process
Touch Screen Calibration with
Software Version 1.00 to 1.02
Touch Screen Calibration is used to force a touch
screen calibration the next time a power cycle
occurs.
1. Press CONSOLE ICON .
2. Press CALIBRATE TOUCH SCREEN ICON .
3. Press HAND ICON to enable the touch
screen calibration process.
4. “Force touch screen calibration next time unit
starts up?”
Press
►Yes – to return to the Touch Screen
Calibration screen. The calibration will be
performed when power to the console is cycled.
►No – to return to the Touch Screen Calibration
screen
5. Press
►PAGE RIGHT ARROW to proceed to
Screenshot.
►SYSTEM SETUP TAB to return to main
System Setup screen.
Figure 2-22: Touch Screen Calibration
Figure 2-23: Touch Screen Calibration
Next Power Cycle
The calibration screen will be displayed before the
console boots.
1. “TSLIB calibration utility Touch crosshair to
calibrate”
Press series of 5 crosshairs .
2. Console will resume booting.
After the fi fth (5th) crosshair is pressed, the
calibration process takes approximately 30 - 45
seconds to complete.
Figure 2-24: Touch Screen Calibration Process
TSLIB calibration utility
Touch crosshair to calibrate
- USER MANUAL 1
- CHAPTER 1– PRODUCT OVERVIEW 7
- SYSTEM FEATURES 7
- Matrix 840G Console 8
- SYSTEM COMPONENTS 8
- Matrix 570G Console 8
- RealView Camera 9
- Video Selector Modules 9
- GPS Antennas 9
- FieldPilot 9
- Steering Control Module 9
- 98-05141 R2 10
- CONFIGURATIONS 11
- Engage/Disengage 12
- POWER ON/OFF 13
- Start Up Sequence 14
- GENERAL OPERATION 14
- INFORMATION 14
- Page Layout and Navigation 15
- CHAPTER 2 – UNIT SETUP 16
- Lightbar 17
- Home Menu 17
- SYSTEM SETUP 17
- LED Brightness 18
- Display Mode 18
- Time Zone 19
- Language 19
- Requirements 20
- GPS Status 20
- GPS Type 20
- GPS Port 20
- LCD Brightness 21
- GGA Requirements 21
- Software Version 1.03 22
- Software Version 1.00 to 1.02 22
- Next Power Cycle 22
- Save About Information 23
- Screenshot 23
- Enable/Disable 23
- Capture an Image 23
- About/Save 23
- Four Channel VSM 24
- Eight Channel VSM 24
- BOOMPILOT/SINGLE 25
- BOOM SETUP 25
- BoomPilot Setup 25
- Number of Boom Sections 26
- Boom Section Width 26
- Delay On 26
- Delay Off 26
- VEHICLE SETUP 27
- Single Boom Setup 27
- TILT GYRO MODULE 28
- Valve Setup 30
- FIELDPILOT SETUP 30
- Autosteer 30
- Cycle Right 31
- Maximum Duty Cycle 31
- Minimum Duty Cycle 31
- Cycle Left 31
- Con gure FieldPilot 32
- Valve Test 32
- Deadband 33
- Coarse Steering Adjustment 33
- Fine Steering Adjustment 33
- Lookahead 34
- CHAPTER 3 – GUIDANCE 35
- GUIDANCE OPERATION 35
- Straight A-B Guidance 35
- GUIDANCE BAR & STATUS BAR 36
- Guidance Bar 36
- Curved A-B Guidance 36
- Circle Pivot Guidance 36
- Last Pass Guidance 36
- VEHICLE VIEW 37
- Status Bar 37
- Vehicle View 38
- Guidance Mode Select 38
- Zoom In/Out & 41
- Perspective 41
- BoomPilot 41
- Field View 42
- Field Boundary 42
- FIELD VIEW 42
- Return to Point 43
- Zoom In/Out 44
- World View 44
- Pan Mode 44
- REALVIEW GUIDANCE 44
- RealView Guidance 45
- Full Screen 45
- Guidance Over Video 45
- Steering Angle Indicator 46
- Single Camera Selection 46
- Split Camera View 47
- Guideline Adjustment 48
- CHAPTER 4 – MONITORING 49
- JOB VIEW 49
- Job Information 49
- Save Information 50
- BOOM MONITORING 51
- Boom Monitor 51
- APPENDIX A ICON REFERENCE 53
- Menu Options 53
- CHAPTER 5 – APPENDIX 53
- Unit Setup 54
- Job View 55
- Guidance Screens 55
- APPENDIX B TIME ZONES 56
- APPENDIX D UNIT 57
- SPECIFICATIONS 57
- APPENDIX C FACTORY 57
- SETTINGS & RANGES 57
Prodotti e manuali riguardandi Computer Teejet Matrix 840G User Manual
(2 pagine)
(2 pagine)
(2 pagine)
(2 pagine)
(2 pagine)
Computer Teejet Matrix 430 Manuale Utente
(12 pagine)
(12 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale