Teejet Matrix 840G User Manual Manuale Utente Pagina 20
- Pagina / 58
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
www.teejet.com
26
●
98-05141 R2
27
●
External Receiver Minimum Confi guration
Requirements
Before the Matrix will connect and work with an
external GPS receiver, these minimum confi guration
requirements must be met.
Serial Port Settings
Baud rate: 19,200
Data Bits: 8
Parity: None
Stop Bits: 1
Serial Port connection requirements
Male 9 pin RS-232 serial cable
NOTE: May require Null modem adapter
depending on pin out of receiver.
NMEA Strings
GGA 5 Hz
VTG 5 Hz
ZDA 0.2 Hz
GPS Status
GPS Status displays information regarding data
rates, number of satellites in view, and satellite
quality and ID.
1. Press GPS ICON .
2. Press GPS PORT ICON to view data
including:
◄GGA/VTG (Data Rates) – the number of GPS
positions per second.
◄Num Sats – the number of GPS satellites in
view (minimum of 4 are required for DGPS)
◄HDOP – a measure of satellite geometry
strength in the horizontal plane. A HDOP value
of less than 2 is preferred.
◄PRN – the current DGPS satellite ID. (see
PRN chart)
◄GGA Quality – the current quality indicator of
the GPS signal. (see GGA chart)
3. Press
►CHECKERED FLAG to complete GPS
Setup.
►SYSTEM SETUP TAB to return to main
System Setup screen.
NOTE: If GPS is not available, all entries will be
“Invalid”
Figure 2-18: GPS Status
GPS Type
GPS Type customizes system to accept GPS source
or DGPS source transmissions.
1. Press GPS ICON .
2. Press GPS TYPE ICON .
3. Select
►GPS Only – uncorrected signals
►DGPS Only – differentially corrected signals
►GPS/DGPS – either type of signal
4. Press
►PAGE RIGHT ARROW to proceed to GPS
Port.
►SYSTEM SETUP TAB to return to main
System Setup screen.
NOTE: This setting is required for FieldPilot and
Tilt Sensor Operation, as well as proper
BoomPilot operation.
Figure 2-16: GPS Type
GPS Port
GPS Port sets port transmission to Internal or
External.
1. Press GPS ICON .
2. Press GPS PORT ICON .
3. Select
►Internal – use the internal (D)GPS (if
equipped) and transmit out
►External – receive external (D)GPS data
4. Press
►PAGE RIGHT ARROW to proceed to GPS
Status.
►SYSTEM SETUP TAB to return to main
System Setup screen.
NOTE: This setting is required for FieldPilot and
Tilt Sensor Operation, as well as proper
BoomPilot operation.
Figure 2-17: GPS Port
NOTE: Working with GPS signals such as Omnistar
HP/XP or RTK will require GPS port to be
set to External.
- USER MANUAL 1
- CHAPTER 1– PRODUCT OVERVIEW 7
- SYSTEM FEATURES 7
- Matrix 840G Console 8
- SYSTEM COMPONENTS 8
- Matrix 570G Console 8
- RealView Camera 9
- Video Selector Modules 9
- GPS Antennas 9
- FieldPilot 9
- Steering Control Module 9
- 98-05141 R2 10
- CONFIGURATIONS 11
- Engage/Disengage 12
- POWER ON/OFF 13
- Start Up Sequence 14
- GENERAL OPERATION 14
- INFORMATION 14
- Page Layout and Navigation 15
- CHAPTER 2 – UNIT SETUP 16
- Lightbar 17
- Home Menu 17
- SYSTEM SETUP 17
- LED Brightness 18
- Display Mode 18
- Time Zone 19
- Language 19
- Requirements 20
- GPS Status 20
- GPS Type 20
- GPS Port 20
- LCD Brightness 21
- GGA Requirements 21
- Software Version 1.03 22
- Software Version 1.00 to 1.02 22
- Next Power Cycle 22
- Save About Information 23
- Screenshot 23
- Enable/Disable 23
- Capture an Image 23
- About/Save 23
- Four Channel VSM 24
- Eight Channel VSM 24
- BOOMPILOT/SINGLE 25
- BOOM SETUP 25
- BoomPilot Setup 25
- Number of Boom Sections 26
- Boom Section Width 26
- Delay On 26
- Delay Off 26
- VEHICLE SETUP 27
- Single Boom Setup 27
- TILT GYRO MODULE 28
- Valve Setup 30
- FIELDPILOT SETUP 30
- Autosteer 30
- Cycle Right 31
- Maximum Duty Cycle 31
- Minimum Duty Cycle 31
- Cycle Left 31
- Con gure FieldPilot 32
- Valve Test 32
- Deadband 33
- Coarse Steering Adjustment 33
- Fine Steering Adjustment 33
- Lookahead 34
- CHAPTER 3 – GUIDANCE 35
- GUIDANCE OPERATION 35
- Straight A-B Guidance 35
- GUIDANCE BAR & STATUS BAR 36
- Guidance Bar 36
- Curved A-B Guidance 36
- Circle Pivot Guidance 36
- Last Pass Guidance 36
- VEHICLE VIEW 37
- Status Bar 37
- Vehicle View 38
- Guidance Mode Select 38
- Zoom In/Out & 41
- Perspective 41
- BoomPilot 41
- Field View 42
- Field Boundary 42
- FIELD VIEW 42
- Return to Point 43
- Zoom In/Out 44
- World View 44
- Pan Mode 44
- REALVIEW GUIDANCE 44
- RealView Guidance 45
- Full Screen 45
- Guidance Over Video 45
- Steering Angle Indicator 46
- Single Camera Selection 46
- Split Camera View 47
- Guideline Adjustment 48
- CHAPTER 4 – MONITORING 49
- JOB VIEW 49
- Job Information 49
- Save Information 50
- BOOM MONITORING 51
- Boom Monitor 51
- APPENDIX A ICON REFERENCE 53
- Menu Options 53
- CHAPTER 5 – APPENDIX 53
- Unit Setup 54
- Job View 55
- Guidance Screens 55
- APPENDIX B TIME ZONES 56
- APPENDIX D UNIT 57
- SPECIFICATIONS 57
- APPENDIX C FACTORY 57
- SETTINGS & RANGES 57
Prodotti e manuali riguardandi Computer Teejet Matrix 840G User Manual
(2 pagine)
(2 pagine)
(2 pagine)
(2 pagine)
(2 pagine)
Computer Teejet Matrix 430 Manuale Utente
(12 pagine)
(12 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale