Teejet Legacy 6000 Manual Manuale Utente Scaricare il pdf (Pagina 157)

Appendix B - Creating Calibration Table152

Since Cal# Basis is not completed during Channel Setup, a new screen •

will be displayed during calibration. The screen will display the same

name entered for Cal# Basis during Channel Setup.

Proceed through the calibration process. Name the parameter and repeat

•

the process for each calibration table parameter.

NOTE: If GATE HEIGHT is to be used for the Cal# Basis name during Channel

Setup, it has already been established as a pre-named parameter in Cali-

bration 1 INCH - 12 INCH.

1 2 ... 152 153 154 155 156 157 158 159

TABLE OF CONTENTS 2
CHAPTER 1 - INTRODUCTION 6
SYSTEM FEATURES 6
Chapter 1 - Introduction2 7
System Components 8
Switch Function Module 9
Input Status Module 10
FieldPilot Module 10
SWATH MANAGER 5 (SM5) 11
LEGACY 6000 CONFIGURATIONS 11
+12v Onl y 12
Chapter 1 - Introduction8 13
45-053 40 14
45-081 06 45-081 06 14
Chapter 1 - Introduction10 15
CHAPTER 2 - SYSTEM OVERVIEW 16
INITIAL POWERUP 17
Chapter 2 - System Overview14 19
Forward Arrow 19
PAGE LAYOUT AND NAVIGATION 20
SYSTEM SETUP 22
Console Setup 23
Lightbar Setup 24
GPS RECEIVER SETUP 25
Implement Setup 26
Chapter 2 - System Overview22 27
CHANNEL SETUP 29
Channel Favorite 30
Application Type 31
Application Type Settings 32
Drive Type 33
Chapter 2 - System Overview30 35
Primary Sensor 37
Primary Sensor Settings 38
SECONDARY SENSOR 39
Settings Description 40
Monitor Selection 41
Monitor Settings 42
Channel Setup Completion 43
Saving Channel Setup 44
FIELDPILOT SETUP 45
FieldPilot Calibration 46
Adjust Oil Flow 47
Drive Straight A-B Line 48
Chapter 2 - System Overview44 49
Chapter 2 - System Overview46 51
Bullseye 52
STARTING JOBS 53
Manually Naming Jobs 54
Automatic Job Naming 55
No PCMCIA Card 55
ARM LAUNCHER 56
Calibration Procedure 57
PRIME INJECTION SYSTEM 58
)NJECTION 59
0RIMING3YSTEM 59
Prime State Reset Values to 0 60
JOB REPORT SETUP 62
Item Description 63
ARM SETUP 64
Entering File Names 66
Swath Manager Lookahead 66
CAN Switchbox 68
Input Status Module (ISM) 69
Swath Manager 5 70
PRODUCT SETUP 71
Product Name Selection 72
Variable Rate Application 73
Tilt Sensor Functions 76
Antenna Height 78
Tilt Sensor Calibration 79
Next softkey (F6) 80
CHAPTER 4 - OPERATION 82
PRODUCT APPLICATION 82
GPS/BOUNDARY PAGE 83
Rate Adjustment 84
Test Speed 85
Reset Initial Quantity 85
FieldPilot Adjustments 86
The Map Page 87
Product Control 88
Chapter 4 - Operation84 89
Solid and Boom Patterns 90
System Messages 91
Warning Messages 91
VEHICLE GUIDANCE 92
Changing Guidance Patterns 93
Straight-Line A-B Guidance 93
Curved A-B Guidance 95
Headland Guidance 96
Ignore Headland Guidance 98
Chapter 4 - Operation94 99
Headland Off 99
Ignore Headland 99
Circle Pivot Guidance 100
Chapter 4 - Operation96 101
Mark B softkey 101
Legacy 6000 102
98-05053 R2 102
FIELDPILOT 103
LIGHTBAR 104
Applied Area Detection 105
MAPPING FIELD BOUNDARIES 106
MAPPING POINTS AND HAZARDS 107
Points Mapping 108
Hazard Mapping 108
EXITING OPERATION 109
SHAPE FILES 110
FIELDWARE MAP MANAGER 111
LIGHTBAR INDEX 111
Chapter 4 - Operation108 113
CHAPTER 5 - SYSTEM TOOLS 114
DEVICE MANAGER 114
Backup Files 115
Restoring System Files 116
Importing Files 116
Speedometer 117
Swath Manager LED Brightness 118
Channels 119
GPS Receiver 121
LightBar 121
Channels 1,2,3 122
CARD MANAGER 123
Chapter 5 - System Tools120 125
CHAPTER 6 - MAPPER 126
DATA SETUP 126
New Job Creation 127
Existing Job Selection 127
Naming Jobs Automatically 127
MAPPER SETUP AND MARKERS 128
Chapter 6 - Mapper124 129
Object Name Creation 130
Object Names Folders 131
MAPPER APPLICATION 132
Chapter 6 - Mapper128 133
Information Page 134
MAPPER TOOLS 135
MAPPER OPTIONS 136
CHAPTER 7 - EXT 138
GUIDANCE ONLY MODE 138
LOG DATA MODE 138
RATE CONTROL MODE 139
RATE CONTROLLER 140
Entering Offset Direction Y 141
Entering Offset Distance Y 142
CONTROLLER SETUP 143
Arrow keys 144
Enter button 144
PRODUCT SETUP OPERATION 145
Product Setup Wizard 146
Select Prescription Map Layer 146
RATES PAGE 147
EXITING OPERATIONS 148
Chapter 7 - EXT144 149
Using the Calibration Table 155
APPENDIX C - NH3 APPLICATION 158

Commenti su questo manuale

Nessun commento

Teejet Legacy 6000 Manual Manuale Utente Pagina 157

Commenti su questo manuale

Prodotti e manuali riguardandi Computer Teejet Legacy 6000 Manual